HOME
NEWS
CONTACT
ACCOUNT
Search
  Advanced Search  
Categories
2005+ Dodge Charger & Challenger->
2006-2009 Trailblazer SS->
2006-2019 Jeep Grand Cherokee SR->
2008-2009 Pontiac G8/G8 GXP->
2010-2022 Camaro->
2014-2016 Chevrolet SS->
Apparel & Misc.
Car Care Products->
Dodge Ram->
Mustang->
1979-1993 Mustang->
1994-2004 Mustang->
2005-2014 Mustang->
Braking->
Cooling System
Driveline->
Engine->
Exhaust->
Exterior->
Fuel & Nitrous->
Ignition->
Induction->
Interior->
Packages
PCM/Electronics->
Suspension/Chassis->
Bushing Kits
Camber Plates
Coilovers
Driveshaft Safety Loop
Front Control Arms
K-Members
Lowering Springs
Motor Mounts
Panhard Bars
Rear Control Arms
Roll Bars/Cages
Shocks/Struts
Strut Tower Brace
Subframe Connectors
Suspension Packages
Swaybars
Toe Rods
Tunnel Brace
Upper Control Arms
Valvetrain->
Wheels->
2015+ Ford Mustang->
Vehicles
82-92 F-Body->
93-97 F-Body->
98-02 F-Body->
1997-2022 Corvette->
04-06 Pontiac GTO->
2004-2020 Cadillac CTS-V->
04-06 Cadillac XLR
1999-2018 GM Trucks->
00-06 Cadillac Escalade
2003-2009 Hummer H2->
Untitled Document
Manufacturers
What's New? more
Nitrous Outlet Wrap Around N2O Heater Element For Mother Bottle
Nitrous Outlet Wrap Around N2O Heater Element For Mother Bottle
$234.99
Online Security

2005+ Ford Mustang UMI Performance Rear Control Arm Relocation Brackets- Bolt In
[1060]


$99.99
   Manufacturer:UMI Performance
   Description:UMI Performance is proud to announce an improvement to our tried and true P/N 1060 lower control arm relocation brackets for the Ford Mustang. With the increasing popularity of 700+ HP cars and corresponding reduction in 60 ft times, we’ve taken the proactive approach and increased material thickness to ¼” in critical locations. We've also added a third adjustment hole and improved the contours in a few key locations. Lower control arm relocation brackets improve forward traction and help tires plant the tires upon launch. Road race and auto-x competitors can use the upper holes to tune roll steer or simply correct lower trailing arm angles on lowered cars.

Wheel hop issues? We have your solution! The S197 chassis is notorious for wheel hop and the more power you add the worse it gets. The UMI Performance control arm relocation brackets are designed to change the instant center point of the vehicle and plant the rear end harder into the ground. By changing the intersecting point of the control arms it allows better weight transfer and forces the rear end into the ground while lifting the body. This technique has been used for many years and has been proven to work over and over again on all types of applications. Relocation brackets are also recommended for lowered vehicles to correct lost suspension geometry caused from height altering.

Installation: These brackets are a 100% bolt on application and require no welding, no drilling and no cutting! All necessary hardware is included for this simple bolt on application. Kit is supplied with hardware, installation instructions and available powder coated red or black.

Lowered Vehicles: When lowering your Mustang you change the lower control arm angle causing the rear mounting point of the control arm to sit higher than the front mounting point. This will, in return, cause wheel hop and a great deal of traction loss. Lower control arm relocation brackets allow you to correct this angle and gain back much needed traction. Relocation brackets are designed to correct instant center, eliminate wheel hop and increase traction. Relocation brackets installed will also help 60-foot times, lower ET’s and increase track consistency--a must for all lowered vehicles!

Non-Lowered Vehicles: Product installed on a stock height vehicle will also see a great increase in traction by lowering the rearward angle of the lower control arm, allowing more force to be placed on the rear tires. Relocation brackets have two settings to allow the lower control arm to be lowered either 2" or 3", depending on your preference. Settings are placed in a correct pattern that will allow use of all OEM control arms or any aftermarket control arm (brackets do not require a longer control arm.) Brackets installed on a non-lowered Mustang can provide a .10 or better 60-foot reduction and an increase in track consistency.

Features:

  • 100% bolt on design that requires no welding, drilling or cutting!
  • CNC machined brackets insure accuracy for a perfect fit
  • Correct hardware is included for this simple installation
  • Durable brilliant powder coat finish
   Available Options: Color:
This product was added to our catalog on Tuesday 20 October, 2009.
Reviews
 Shopping Cart more
0 items
Manufacturer Info
UMI Performance
Other products
Reviews more
Write a review on this product!
Sites We Sponsor
Information